20 Fun Details About Double Glazing Door Lock Repairs

Double Glazing Door Lock Repairs

Are you experiencing issues with your uPVC window or door mechanism faulty? Perhaps the door or window handles aren't aligned properly or are difficult to use.

You'll be wasting energy if your double-glazed doors don't function properly. This also increases the likelihood of burglaries. Owen the Locksmith will be able to repair your door lock at an affordable price.

Snapped Key

When a key snaps off within the lock, it can be incredibly annoying. It also poses an issue for security, since the door may not lock and could leave you open to intrusion. There are a few quick fixes you can try to resolve the issue and make your door functional again.

Keep calm. If you panic you may end up pushing the damaged key further into the lock.

Next spray WD-40 or another penetrating oil into the lock to make the broken piece slip out more easily. You can also use the screwdriver to break up any pieces that are stuck. If you happen to have a small piece of the key that is visible and you want to remove it, make use of a paperclip, or any other thin metal object to grab it and pull it out. Both methods work, but you must be careful not to push the broken key piece further into the keyway.

Some paperclips have grooved edges which can be used as hook extractors. Jigsaw blades can also work well for this. If you don't happen to have any of these, you can bend a hook with needle-nosed pliers. Additionally, you can make use of a pair of tweezers to grab and remove the last bit of the broken keys.

If you are unable to remove the broken key piece then you can use a lock deicer. It's available at most hardware stores and is used to freeze any moisture that may be present within the lock.

If none of these solutions seem to work, it may be time to contact a locksmith. Fitlocks experts can quickly fix problems with uPVC door mechanisms and locks, including snapped keys and broken handles. They can also reconfigure double glazing door mechanisms so that they are more easy to use. You can book a double-glazing repair online or contact us to discuss your requirements.

Broken Cylinder

A broken cylinder is an extremely risky security issue. A locksmith professional can fix the cylinder. Locksmiths will need to tap the cylinder in order to repair it. This can be done using a hammer, or any other tool. The best method is to make use of a wire or a long match. The match or wire end near the keyway. After this, the locksmith will strike the lock and break it open. This is better than using a hammer, which can damage the lock.

The most frequent cause for cracks in the cylinder head is overheating. This can occur when the block and cylinder head are made of different metals, such as cast-iron or aluminium. When various metals heat up and cool down at different rates, it could create hotspots in the local area that expand faster than the rest of the cylinder head, leading to cracks.

double glazing repairs near me of cylinder cracks is corrosion. If the cylinder block and head are not maintained correctly they could rust or corrode and cause them to expand faster than anticipated. In time, this could also lead to cracks.

If your uPVC window or door lock is brittle or requires a lot of pressure to turn, this can be caused by a number of things. A faulty locking mechanism, misalignment or the wear of the handle are typical reasons for this issue.

Fortunately, this is an easy and cost-effective fix for the majority of double glazing owners. A professional locksmith will usually be able to resolve the issue within an hour of arriving at your home. Based on your requirements they will be able to replace the locking mechanism, change the window handles, and also change the gearboxes. A professional locksmith can always advise you on the most cost-effective solutions for your home. They can even suggest upgrades to 3 Star security TS007 euro cylinders that will give you an additional layer of security against burglars. This is a small price to pay for the peace of mind that comes from knowing your uPVC doors are safe.

Broken Handle

Window handle locks are complex mechanisms that become less effective with time and use, so it's no surprise that they sometimes break. If yours is damaged it may be difficult to pinpoint the cause of the issue. Make sure you fix it correctly.

The issue could be related to the locking mechanism inside or the latch, fixing your broken handle will improve your uPVC double glazing door's security and allow you stop drafts. If you do not repair or replace your handle can be costly and may damage the door's frame and lock, so it's worth taking some time to do it correctly.

Screwdriver When the window is open remove the screw that holds the handle. It should be located on the inside face of the back plate, which is usually covered by an aesthetically pleasing cover for the screw reasons. It is not recommended to lose any internal components of the handle, such as the levers and plates on either side. It is best to keep them in the same order so you can re-install them in the event of a need.

Then, with an additional screwdriver take the screw off that connects the handle with the spindle on the back. Once the screw is loose, remove the handle and take out the broken spindle. Replace it with a new spindle, ensuring it's the same length (you can find them online or at hardware stores). Screw it in the frame. Do not tighten the screw too much as this can harm the handle as well as the window frame.

Make sure the new handle is installed Close the window and test the handle. It should function smoothly, and you will be able to open your windows once more.

While you're working on the handle, make sure to make sure your uPVC windows are shut properly. If they don't close properly, you could experience damp or draughts inside your home. It could also affect the energy efficiency of your home. Core Sash Windows is a local window company that can alter the hinges on the window frames to ensure that they close correctly.

Broken Spindle

It is more common for the spindle to break than the handle. This is particularly common with uPVC tilt-and-turn windows. These kinds of windows require a handle that operates a locking mechanism in the frame of the window. The handle is attached to a central rod which is then activated by a series of mushroom-like locking cams, these locks are inserted into the window frame. If the dead latch mechanism does not open when the handle is turned it is likely that the spindle has broken, this can be an extremely frustrating issue.

Luckily, there are steps that can be taken to remedy this situation. A good locksmith can quickly and efficiently repair this issue. A good locksmith can disassemble the window's handle using a tool that removes the wheel from the area where the spindle is located. This can be done with no damage to the handle or window frame.

Once the wheel is removed, the technician can inspect the spindle and determine what has caused it to break. This involves breaking down the spindle into its component parts and carefully recording their general condition as well as any specific areas of wear or damage. This procedure is typically performed by technicians in an environment that is clean.

The next step is to clean the damaged spindle. This will help get rid of any dirt or other debris that might be preventing it from functioning normally. The spindle may then be repaired or replaced. If the technician is replacing the spindle, it is possible to use a dowel that is the same size to the original. He will then drill matching holes into both pieces. This will ensure that the new spindle is precisely matched to the handle.





If the spindle is damaged and cannot be repaired, it could need to be replaced entirely. Home centres sell generic substitutes but if the window design is unique you'll have to speak with an expert in cabinet making or woodworking who can make the exact piece. Once the spindle has been installed, it can be attached to the handle. Line up the screw holes on the handle to the screws already in the frame. Once the new handle is in place, you'll be able to operate your uPVC window.